How to do DMA transfers under DOS extender or DPMI environment?

Question

How can a program use DMA transfers while running under a DOS extender+DPMI environment ?

I mean how can we allocate and get physical address of the dma buffer allocated, so as to supply that physical address to the DMA controller, or PCI bus master device.

There are two possiblities:

The DOS Extender or DPMI server/host support virtual memory. eg Causeway.

The DOS Extender or DPMI server/host doesn't support virtual memory, but paging is enabled. eg DOS32a.

I'm using Open Watcom C compiler.

The runtime environment is :

FreeDOS + XMS(no EMS/EMM386) + DOS extender(DOS32a)

For DJGPP, the solution is here

But will that last mentioned solution ie via XMS, work with DOS32a too?

DOS32a docs say that before switching to protected mode, it allocates all of the available extended memory, and then our program can allocate that memory via DPMI function 501h.

NOTE: The dma buffer can be 1MB or so, so I can't use conventional memory for it.

Alexey Frunze · Accepted Answer · 2012-07-30T06:49:42.947

For a clean DPMI solution you may want to explore the following DPMI functions (excerpts from Ralf Brown's Interrupt List):

INT 31 P - DPMI 1.0+ - MAP DEVICE IN MEMORY BLOCK
        AX = 0508h
        ESI = memory block handle
        EBX = page-aligned offset within memory block of page(s) to be mapped
        ECX = number of pages to map
        EDX = page-aligned physical address of device
Return: CF clear if successful
        CF set on error
            AX = error code (8001h,8003h,8023h,8025h) (see #03143)
Notes:  only supported by 32-bit DPMI hosts, but may be used by 16-bit clients
        support of this function is optional; hosts are also allowed to support
          the function for some devices but not others

INT 31 P - DPMI 1.0+ - MAP CONVENTIONAL MEMORY IN MEMORY BLOCK
        AX = 0509h
        ESI = memory block handle
        EBX = page-aligned offset within memory block of page(s) to map
        ECX = number of pages to map
        EDX = page-aligned linear address of conventional (below 1M) memory
Return: CF clear if successful
        CF set on error
            AX = error code (8001h,8003h,8023h,8025h) (see #03143)
Notes:  only supported by 32-bit DPMI hosts, but may be used by 16-bit clients
        support of this function is optional

INT 31 P - DPMI 0.9+ - PHYSICAL ADDRESS MAPPING
        AX = 0800h
        BX:CX = physical address (should be above 1 MB)
        SI:DI = size in bytes
Return: CF clear if successful
            BX:CX = linear address which maps the requested physical memory
        CF set on error
            AX = error code (DPMI 1.0+) (8003h,8021h) (see #03143)
Notes:  implementations may refuse this call because it can circumvent protects
        the caller must build an appropriate selector for the memory
        do not use for memory mapped in the first megabyte

If neither of the above lets you map virtual addresses to physical addresses nor obtain physical addresses of allocated blocks (e.g. unsupported), you'll need to look into implementation details of your DPMI host (e.g. if it doesn't enable page translation or it can be turned off, then all addresses are physical).

EDIT: It looks like you should be able to allocate memory (more than and beyond 1MB) and get its physical and virtual addresses. First, allocate it using XMS/Himem.sys and lock it. That'll give you the physical address. Next, use the DPMI function 0x800 to get the corresponding virtual address.

Here's how (disregard the 16-bit version (compiled with Borland/Turbo C/C++), it's only used only to validate the XMS routines):

// file: dma.c
//
// Compiling with Open Watcom C/C++ and DOS/32 DOS extender/DPMI host:
//   wcl386.exe /q /we /wx /bcl=dos4g dma.c
//   sb.exe /b /bndmados32.exe dma.exe
// Before running dmados32.exe do "set DOS32A=/EXTMEM:4096"
// to limit the amount of extended (XMS) memory allocated by DOS/32
// at program start (by default it allocates everything).
//
// Compiling with 16-bit Borland/Turbo C/C++:
//   tcc.exe dma.c

#include <stdio.h>
#include <string.h>
#include <dos.h>
#include <limits.h>

#if defined(__WATCOMC__)
#if !defined(__386__)
#error unsupported target, must be 32-bit (DPMI) DOS app
#endif
#elif defined(__TURBOC__)
#if !defined(__SMALL__)
#error unsupported target, must be 16-bit DOS app with small memory model
#endif
#else
#error unsupported compiler
#endif

typedef unsigned uint;
typedef unsigned long ulong;

typedef signed char int8;
typedef unsigned char uint8;

typedef short int16;
typedef unsigned short uint16;

#if UINT_MIN >= 0xFFFFFFFF
typedef int int32;
typedef unsigned uint32;
#else
typedef long int32;
typedef unsigned long uint32;
#endif

#pragma pack(push, 1)

typedef struct tDpmiRmInt
{
  uint32 edi, esi, ebp, resz0, ebx, edx, ecx, eax;
  uint16 flags, es, ds, fs, gs, ip, cs, sp, ss;
} tDpmiRmInt;

#pragma pack(pop)

int RmInt(uint8 IntNumber, tDpmiRmInt* pRegs)
{
#if defined(__WATCOMC__)
  union REGS inregs, outregs;

  memset(&inregs, 0, sizeof(inregs));
  memset(&outregs, 0, sizeof(outregs));

  inregs.w.ax = 0x300;
  inregs.h.bl = IntNumber;
  inregs.h.bh = 0;
  inregs.w.cx = 0;
  inregs.x.edi = (uint32)pRegs;

  return int386(0x31, &inregs, &outregs);
#elif defined(__TURBOC__)
  struct REGPACK regs;

  memset(&regs, 0, sizeof(regs));

  regs.r_ax = (uint16)pRegs->eax;
  regs.r_bx = (uint16)pRegs->ebx;
  regs.r_cx = (uint16)pRegs->ecx;
  regs.r_dx = (uint16)pRegs->edx;
  regs.r_si = (uint16)pRegs->esi;
  regs.r_di = (uint16)pRegs->edi;
  regs.r_bp = (uint16)pRegs->ebp;
  regs.r_flags = pRegs->flags;
  regs.r_ds = pRegs->ds;
  regs.r_es = pRegs->es;

  // No fs, gs (16-bit code)
  // No ss:sp, cs:ip (int*()/intr() functions set the right values)

  intr(IntNumber, &regs);

  memset(pRegs, 0, sizeof(*pRegs));

  pRegs->eax = regs.r_ax;
  pRegs->ebx = regs.r_bx;
  pRegs->ecx = regs.r_cx;
  pRegs->edx = regs.r_dx;
  pRegs->esi = regs.r_si;
  pRegs->edi = regs.r_di;
  pRegs->ebp = regs.r_bp;
  pRegs->flags = regs.r_flags;
  pRegs->ds = regs.r_ds;
  pRegs->es = regs.r_es;

  return regs.r_ax;
#endif
}

int RmFarCall(tDpmiRmInt* pRegs)
{
#if defined(__WATCOMC__)
  union REGS inregs, outregs;

  memset(&inregs, 0, sizeof(inregs));
  memset(&outregs, 0, sizeof(outregs));

  inregs.w.ax = 0x301;
  inregs.h.bh = 0;
  inregs.w.cx = 0;
  inregs.x.edi = (uint32)pRegs;

  return int386(0x31, &inregs, &outregs);
#elif defined(__TURBOC__)
  uint8 code[128];
  uint8* p = code;
  void far* codef = &code[0];
  void (far* f)(void) = (void(far*)(void))codef;

  *p++ = 0x60;                                                            // pusha
  *p++ = 0x1E;                                                            // push  ds
  *p++ = 0x06;                                                            // push  es

  *p++ = 0x68; *p++ = (uint8)pRegs->ds; *p++ = (uint8)(pRegs->ds >> 8);   // push #
  *p++ = 0x1F;                                                            // pop  ds
  *p++ = 0x68; *p++ = (uint8)pRegs->es; *p++ = (uint8)(pRegs->es >> 8);   // push #
  *p++ = 0x07;                                                            // pop  es

  *p++ = 0xb8; *p++ = (uint8)pRegs->eax; *p++ = (uint8)(pRegs->eax >> 8); // mov ax, #
  *p++ = 0xbb; *p++ = (uint8)pRegs->ebx; *p++ = (uint8)(pRegs->ebx >> 8); // mov bx, #
  *p++ = 0xb9; *p++ = (uint8)pRegs->ecx; *p++ = (uint8)(pRegs->ecx >> 8); // mov cx, #
  *p++ = 0xba; *p++ = (uint8)pRegs->edx; *p++ = (uint8)(pRegs->edx >> 8); // mov dx, #
  *p++ = 0xbe; *p++ = (uint8)pRegs->esi; *p++ = (uint8)(pRegs->esi >> 8); // mov si, #
  *p++ = 0xbf; *p++ = (uint8)pRegs->edi; *p++ = (uint8)(pRegs->edi >> 8); // mov di, #
  *p++ = 0xbd; *p++ = (uint8)pRegs->ebp; *p++ = (uint8)(pRegs->ebp >> 8); // mov bp, #

  *p++ = 0x9A; *p++ = (uint8)pRegs->ip; *p++ = (uint8)(pRegs->ip >> 8);
               *p++ = (uint8)pRegs->cs; *p++ = (uint8)(pRegs->cs >> 8);   // call far seg:offs

  *p++ = 0x60;                                                            // pusha
  *p++ = 0x1E;                                                            // push  ds
  *p++ = 0x06;                                                            // push  es
  *p++ = 0x89; *p++ = 0xE5;                                               // mov   bp, sp
  *p++ = 0x8E; *p++ = 0x5E; *p++ = 0x16;                                  // mov   ds, [bp + 0x16]
  *p++ = 0x89; *p++ = 0xEE;                                               // mov   si, bp
  *p++ = 0xFC;                                                            // cld

  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->es; *p++ = (uint8)((uint16)&pRegs->es >> 8);  // mov [], ax (es)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->ds; *p++ = (uint8)((uint16)&pRegs->ds >> 8);  // mov [], ax (ds)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->edi; *p++ = (uint8)((uint16)&pRegs->edi >> 8);  // mov [], ax (di)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->esi; *p++ = (uint8)((uint16)&pRegs->esi >> 8);  // mov [], ax (si)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->ebp; *p++ = (uint8)((uint16)&pRegs->ebp >> 8);  // mov [], ax (bp)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->ebx; *p++ = (uint8)((uint16)&pRegs->ebx >> 8);  // mov [], ax (bx)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->edx; *p++ = (uint8)((uint16)&pRegs->edx >> 8);  // mov [], ax (dx)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->ecx; *p++ = (uint8)((uint16)&pRegs->ecx >> 8);  // mov [], ax (cx)
  *p++ = 0xAD;                                                            // lodsw          
  *p++ = 0xA3; *p++ = (uint8)&pRegs->eax; *p++ = (uint8)((uint16)&pRegs->eax >> 8);  // mov [], ax (ax)

  *p++ = 0x83; *p++ = 0xC4; *p++ = 0x14;                                  // add   sp, 0x14

  *p++ = 0x07;                                                            // pop   es
  *p++ = 0x1F;                                                            // pop   ds
  *p++ = 0x61;                                                            // popa
  *p++ = 0xCB;                                                            // retf

  f();

  return (uint16)pRegs->eax;
#endif
}

struct
{
  uint16 Ip, Cs;
} XmsEntryPoint = { 0 };

int XmsSupported(void)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x4300;
  RmInt(0x2F, &regs);

  return (regs.eax & 0xFF) == 0x80;
}

void XmsInit(void)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x4310;
  RmInt(0x2F, &regs);

  XmsEntryPoint.Cs = regs.es;
  XmsEntryPoint.Ip = (uint16)regs.ebx;
}

int XmsQueryVersions(uint16* pXmsVer, uint16* pHimemVer)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x00 << 8;
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  if (pXmsVer != NULL)
    *pXmsVer = (uint16)regs.eax;

  if (pHimemVer != NULL)
    *pHimemVer = (uint16)regs.ebx;

  return (int)(regs.ebx & 0xFF);
}

int XmsQueryFreeMem(uint16* pLargest, uint16* pTotal)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x08 << 8;
  regs.ebx = 0;
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  if (pLargest != NULL)
    *pLargest = (uint16)regs.eax;

  if (pTotal != NULL)
    *pTotal = (uint16)regs.edx;

  return (int)(regs.ebx & 0xFF);
}

int XmsAllocMem(uint16* pHandle, uint16 Size)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x09 << 8;
  regs.edx = Size;
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  *pHandle = (uint16)regs.edx;

  return (int)(regs.ebx & 0xFF);
}

int XmsFreeMem(uint16 Handle)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x0A << 8;
  regs.edx = Handle;
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  return (int)(regs.ebx & 0xFF);
}

int XmsLockMem(uint16 Handle, uint32* pPhysAddr)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x0C << 8;
  regs.edx = Handle;
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  *pPhysAddr = ((regs.edx & 0xFFFF) << 16) | (regs.ebx & 0xFFFF);

  return (int)(regs.ebx & 0xFF);
}

#if defined(__TURBOC__)
int XmsCopyMem(uint16 DstHandle, uint32 DstOffs, uint16 SrcHandle, uint32 SrcOffs, uint32 Size)
{
  tDpmiRmInt regs;
#pragma pack(push, 1)
  struct
  {
    uint32 Size;
    uint16 SrcHandle;
    uint32 SrcOffs;
    uint16 DstHandle;
    uint32 DstOffs;
  } emm;
#pragma pack(pop)

  emm.Size      = Size;
  emm.SrcHandle = SrcHandle;
  emm.SrcOffs   = SrcOffs;
  emm.DstHandle = DstHandle;
  emm.DstOffs   = DstOffs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x0B << 8;
  regs.ds = FP_SEG(&emm);
  regs.esi = FP_OFF(&emm);
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  return (int)(regs.ebx & 0xFF);
}
#endif

int XmsUnlockMem(uint16 Handle)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x0D << 8;
  regs.edx = Handle;
  regs.cs = XmsEntryPoint.Cs;
  regs.ip = XmsEntryPoint.Ip;
  RmFarCall(&regs);

  return (int)(regs.ebx & 0xFF);
}

#if defined(__WATCOMC__)
int DpmiMap(void** pPtr, uint32 PhysAddr, uint32 Size)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x800;
  regs.ebx = PhysAddr >> 16;
  regs.ecx = PhysAddr & 0xFFFF;
  regs.esi = Size >> 16;
  regs.edi = Size & 0xFFFF;
  RmInt(0x31, &regs);

  *pPtr = (void*)(((regs.ebx & 0xFFFF) << 16) | (regs.ecx & 0xFFFF));

  return regs.flags & 1;
}

int DpmiUnmap(void* Ptr)
{
  tDpmiRmInt regs;

  memset(&regs, 0, sizeof(regs));
  regs.eax = 0x801;
  regs.ebx = (uint32)Ptr >> 16;
  regs.ecx = (uint32)Ptr & 0xFFFF;
  RmInt(0x31, &regs);

  return regs.flags & 1;
}
#endif

int main(void)
{
  uint16 xmsVer, himemVer;
  uint16 largestFreeSz, totalFreeSz;
  uint16 handle;
  uint32 physAddr;

#if defined(__WATCOMC__)
  {
    uint32 cr0__ = 0, cr3__ = 0;
    __asm
    {
      mov eax, cr0
      mov cr0__, eax
      mov eax, cr3
      mov cr3__, eax
    }
    printf("CR0: 0x%08lX, CR3: 0x%08lX\n", (ulong)cr0__, (ulong)cr3__);
  }
#endif

  if (!XmsSupported())
  {
    printf("XMS unsupported\n");
    goto Exit;
  }
  printf("XMS supported\n");

  XmsInit();
  printf("XMS entry point: 0x%04X:0x%04X\n",
         XmsEntryPoint.Cs, XmsEntryPoint.Ip);

  XmsQueryVersions(&xmsVer, &himemVer);
  printf("XMS version: 0x%X  Himem.sys version: 0x%X\n",
         xmsVer, himemVer);

  XmsQueryFreeMem(&largestFreeSz, &totalFreeSz);
  printf("Largest free block size: %u KB  Total free memory: %u KB\n",
         largestFreeSz, totalFreeSz);

  printf("Allocating the DMA buffer...\n");
  if (XmsAllocMem(&handle, 64))
  {
    printf("Failed to allocate the DMA buffer\n");
    goto Exit;
  }

  XmsQueryFreeMem(&largestFreeSz, &totalFreeSz);
  printf("Largest free block size: %u KB  Total free memory: %u KB\n",
         largestFreeSz, totalFreeSz);

  printf("Locking the DMA buffer...\n");
  if (XmsLockMem(handle, &physAddr))
  {
    printf("Failed to lock the DMA buffer\n");
  }
  else
  {
    printf("The DMA buffer is at physical address: 0x%08lX\n", (ulong)physAddr);

#if defined(__WATCOMC__)
    {
      uint8* ptr;

      printf("Mapping the DMA buffer...\n");

      if (DpmiMap((void**)&ptr, physAddr, 64 * 1024UL))
      {
        printf("Failed to map the DMA buffer\n");
      }
      else
      {
        printf("The DMA buffer is at virtual address: 0x%08lX\n", (ulong)ptr);

        printf("Using the DMA buffer...\n");
        strcpy(ptr, "This is a test string in the DMA buffer.");
        printf("%s\n", ptr);

        DpmiUnmap(ptr);
      }
    }
#elif defined(__TURBOC__)
    {
      char testStr[] = "This is a test string copied to and from the DMA buffer.";
      printf("Using the DMA buffer...\n");
      if (XmsCopyMem(handle, 0, 0, ((uint32)FP_SEG(testStr) << 16) + FP_OFF(testStr), sizeof(testStr)))
      {
        printf("Failed to copy to the DMA buffer\n");
      }
      else
      {
        memset(testStr, 0, sizeof(testStr));
        if (XmsCopyMem(0, ((uint32)FP_SEG(testStr) << 16) + FP_OFF(testStr), handle, 0, sizeof(testStr)))
        {
          printf("Failed to copy from the DMA buffer\n");
        }
        else
        {
          printf("%s\n", testStr);
        }
      }
    }
#endif

    XmsUnlockMem(handle);
  }

  XmsFreeMem(handle);

  XmsQueryFreeMem(&largestFreeSz, &totalFreeSz);
  printf("Largest free block size: %u KB  Total free memory: %u KB\n",
         largestFreeSz, totalFreeSz);

Exit:

  return 0;
}

Sample output (under DosBox):

CR0: 0x00000001, CR3: 0x00000000
XMS supported
XMS entry point: 0xC83F:0x0010
XMS version: 0x300  Himem.sys version: 0x301
Largest free block size: 11072 KB  Total free memory: 11072 KB
Allocating the DMA buffer...
Largest free block size: 11008 KB  Total free memory: 11008 KB
Locking the DMA buffer...
The DMA buffer is at physical address: 0x00530000
Mapping the DMA buffer...
The DMA buffer is at virtual address: 0x00530000
Using the DMA buffer...
This is a test string in the DMA buffer.
Largest free block size: 11072 KB  Total free memory: 11072 KB

Note that DOS/32 does not enable page translation (unless there's VCPI). CR0's PG bit is 0, CR3 is 0 and the obtained physical and virtual addresses are the same, everything speaks for that. And so the virtual and physical addresses are the same thing.

The DPMI functions you mentioned are for mapping *physical address to virtual/linear address* and *not* for mapping virtual address to physical address. I need to map virtual address to physical address, after *allocating* a dma buffer from DOS extender/DPMI host. Also DOS32a supports only DPMI0.9 functions with one or two exceptions like 0801h etc. The question is to *how can I allocate and obtain the physical address of the dma buffer*. The dma buffer can be upto 1MB or so, so I can't use conventional memory for it. :) — jacks, Jul 28 '12 at 04:06
You can first get the physical address and then the virtual address from it with function 800h. See the updated answer. — Alexey Frunze, Jul 30 '12 at 06:51
+1 for suggesting that track. :) I was also working with something like this and read CR0 with paging disabled(when no EMM386 ie VCPI or EMS driver is loaded). CR3 was 0 too as expected. Though I didn't verify that addresses of buffer allocated via DPMI calls 501h match the physical addresses(becoz I'm stucked with other issues not related to this post),but seems that they should be same. To further confirm whether CR0 and CR3 have right values returned, I read CS register and get the associated descriptor and determine the DPL bits - they were 00b - ie my program is running in ring0, so... — jacks, Aug 01 '12 at 07:50
that privileged instructions(reading and writing control registers) are not simulated by fault handler installed by DOS32A. — jacks, Aug 01 '12 at 07:51
You have DOS/32 source code, you can confirm that it does not enable page translation. Look at the initialization code (search for cr0 and cr3 and look at the code using them). — Alexey Frunze, Aug 01 '12 at 17:04
Well, I'm not so good at assembly stuff, so I avoided that at first . But now I think it will be worth to have a look at the source code, if I can find something. :) — jacks, Aug 03 '12 at 03:01

liaoo · Answer 2 · 2012-08-16T02:18:08.220

I wrote an app to test AHCI in DOS(my environment was DOS 7.0 + DOS32a + Watcom C) and I listed how I allocated memory for DMA transfer as below for your reference.

(1) allocate memory in flat mode ( assume allocate 1K memory and should be WORD align)

ptr = (pDWORD)calloc(1024+1, sizeof(BYTE));

where 1024 is what we really need and 1Byte is for "tolerance" because the returned pointer may not be word-align and the worst case is Ex. ptr points to 0x30000001

(2) adjust based on WORD(2-byte) align

if(inputAddr & 1) { inputAddr &= (~2 + 1); inputAddr += 2; }

(3) assign the inputAddr above to PRDT's DBA(Data Base Address)

Notes:

1) I used "flat memory mode" by "...wpp386 -mf ..." in makefile and "op stub=dos23a.exe" in linker file...

2) where ptr is the actual pointer to allocated memory portion and should be kept when releasing memory; inputAddr is another pointer pointing to the correct(aligned) memory address for data transfer !

By this way DMA transfer test was OK and allocated memory can be up to 4MB in this environment...

F.Y.I

How to do DMA transfers under DOS extender or DPMI environment?

2 Answers2