6

I am trying to configure LIRC to work with my Raspberry 2B and a circuit I build with a transistor and a IR transmitter as explained in this tutorial

After the installation of LIRC, I followed all the steps and I added these two lines in /etc/modules

lirc_dev
lirc_rpi gpio_out_pin=36

Then I typed this in /etc/lirc/hardware.conf

LIRCD_ARGS="--uinput"
LOAD_MODULES=true
DRIVER="default"
DEVICE="/dev/lirc0"
MODULES="lirc_rpi"
LIRCD_CONF=""
LIRCMD_CONF=""

After rebooting, I added the configuration of my Samsung remote (BN59-00516A) to /etc/lirc/lircd.conf

Then I restarted LIRC again but when I run a command to send a IR frequency 

irsend SEND_ONCE Samsung_BN59-00865A KEY_POWER

it complains with the following error:

irsend: could not connect to socket

irsend: No such file or directory

I am guessing this is a problem with my device socket, because in the hardware.conf file I set

DEVICE = "/dev/lirc0"

(just because the tutorial states it), but lirc0 file isn't within the folder. I couldn't find any other question related to this problem and google didn't help me much either. Does anyone have any hint on this?

muilpp
  • 1,293
  • 4
  • 17
  • 36

5 Answers5

4

After googling a lot, I found out an update is needed to have everything working properly. In my case I did:

apt-get update, apt-get upgrade, rpi-update

Also, as pointed out in this other tutorial, depending on the Raspberry firmware, you might need to add this to /boot/config.txt

dtoverlay=lirc-rpi,gpio_in_pin=XX,gpio_out_pin=YY

Substitute X and Y for whatever pins you're using!

muilpp
  • 1,293
  • 4
  • 17
  • 36
3

I had a similar problem and I solved it with this command:

sudo lircd --device /dev/lirc0

If you set the value of LIRCD_ARGS in /etc/lirc/hardware.conf to "--device /dev/lirc0", it should start lircd appropriately, when /etc/init.d/lirc is started at boot.

Community
  • 1
  • 1
Thomas
  • 31
  • 1
1

you need to run lircd. It will create two files (lircd and lircd.pid) at /var/run/lirc/:

lircd
Jeff Pal
  • 1,519
  • 1
  • 17
  • 28
0

I got the same error messages. But had all configurations done. The restart of the lirc daemon solved this issue by typing $ sudo /etc/init.d/lirc restart

R.Schied
  • 71
  • 3
0

I think is useful to say that the gpio_in_pin=XX,gpio_out_pin=YY part of the /etc/modules can be double checked with dmesg | grep lirc which results in something like

[    3.437499] lirc_dev: IR Remote Control driver registered, major 244
[    5.472916] lirc_rpi: module is from the staging directory, the quality is unknown, you have been warned.
[    6.621156] lirc_rpi: auto-detected active high receiver on GPIO pin 22
[    6.622515] lirc_rpi lirc_rpi: lirc_dev: driver lirc_rpi registered at minor = 0
[    6.622528] lirc_rpi: driver registered!

for /etc/modules containing

lirc_dev
lirc_rpi gpio_in_pin=23 gpio_out_pin=22
Rho Phi
  • 1,182
  • 1
  • 12
  • 21