Sending API tx frame from coordinator to end device (zigbee+arduino)

Question

Hi i'm developing a WSN where every end device before starting transmitting must receive a call from the Coordinator. For testing purpose I'm working with 4 Arduino nano 3.0 (in the final configuration i will use a different microcontroller with an M3 cortex cpu) and four XBee (xb24-b with zb firmware). I am not able to send a message from the coordinator to the selected end device, meanwhile i successfully accomplish to transmit data from end device to the coordinator. here the code running on the arduino on the coordinator node. The end device is directly connect to the pc with an USB explorer.

   #include <SoftwareSerial.h> 
// creo una porta seriale di tipo software sui pin 2(RX) e 3(TX)
uint8_t rxxbee = 2;
uint8_t txxbee = 3;
SoftwareSerial Serial_xbee(rxxbee,txxbee);


// variable to store the data received
int sensorValue = 0;

// costant values of the frame
const byte startDelimeter = 0x7E;

  // length
const byte MSB_1 = 0x00;
const byte LSB_2 = 0x10;  

  // Frame-specific data
const byte frameType = 0x10;
const byte frameID = 0x0;

  // 64-bit destination address 
const byte MSB_5  = 0x00;
const byte b_6    = 0x13;
const byte b_7    = 0xA2;
const byte b_8    = 0x00;
const byte b_9    = 0x40;
const byte b_10   = 0x86;
const byte b_11   = 0xDB;
const byte LSB_12 = 0xA4;

  // 16-bit destination network address
const byte MSB_13 = 0x0;
const byte LSB_14 = 0x0;

  // broadcast radius
const byte broadcastRadius = 0x0;

  // options
const byte opt = 0x0;


byte spedisci (byte value) {
Serial_xbee.write(value);
Serial.write(value);
return value;
}


void setup()
{
  // starts serial communication
  Serial.begin(9600);
  Serial_xbee.begin(9600);
  pinMode(sensorPin, INPUT);

}

void loop()
{
  // send data through xBee
  spedisci(startDelimeter);
  spedisci(MSB_1);
  spedisci(LSB_2);
  long sum = 0; // accumulate the checksum  
  sum += spedisci(frameType);
  sum += spedisci(frameID);
  sum += spedisci(MSB_5);
  sum += spedisci(b_6);
  sum += spedisci(b_7);
  sum += spedisci(b_8);
  sum += spedisci(b_9);
  sum += spedisci(b_10);
  sum += spedisci(b_11);
  sum += spedisci(LSB_12);
  sum += spedisci(MSB_13);
  sum += spedisci(LSB_14);
  sum += spedisci(broadcastRadius);
  sum += spedisci(opt);
  sum += spedisci(0X10);  // this is the payload[0] byte
  sum += spedisci(0X10);  // this is the payload[1] byte
  spedisci( 0xFF - (sum & 0xFF));
}

Any suggestion?

thanks!

Ps the coordinator api firmware is 21A7; the end device api firmware is 29A7

score 1 · Accepted Answer · answered Jan 21 '14 at 22:30

1

I think that when using the 64-bit IEEE address of a node that is not the coordinator, you need to use 0xFFFE as the 16-bit network address. Try changing this section of your code:

// 16-bit destination network address
const byte MSB_13 = 0xFF;
const byte LSB_14 = 0xFE;

When you're ready to move away from the Arduino platform, take a look at this Open Source, portable, ANSI C XBee Host Library for communicating with the XBee radio in API mode. It could simplify a lot of your software development.

answered Jan 21 '14 at 22:30

tomlogic

11,489
3
33
59

Great it WORKS!!!!!!!!! I have just another two question do you know why XCTU don't allow me to put SM 0 for the end device? (even if the no sleep firmware is available?) and i take a look to your library but i'm not an software engineering (just a materials engineering and all my knowledge of software developping is on C/fortran/matlab code for scientific programming and this is the first time that i should trouble with libraries) and i'm not able to understand if the libraries is compatible with maple mini board [link](http://leaflabs.com/docs/hardware/maple-mini.html). Is it compatible? – Andrea Jan 22 '14 at 16:28
Try installing router firmware (23A7?) if you don't want the device to sleep. I seem to recall that Digi split the single router/end device firmware build into separate builds on that platform. As for the Maple Mini, it should be possible to port the host library to that platform, but it might be difficult for a non-SW Engineer to get it up and running. – tomlogic Jan 24 '14 at 02:29

Sending API tx frame from coordinator to end device (zigbee+arduino)

1 Answers1